>SeniorScore |
>La Villa Strangiato |
| (не показано 13 промежуточных версий 7 участников) |
| Строка 1: |
Строка 1: |
| == Introduction: Shields and you. Why bother? ==
| | [[File:SetupShields-ShieldRoom.png|thumb|The shield room in engineering.]] |
|
| |
|
| | The shields, as the name implies, protects the [[SCCV Horizon]] from all manner of outer space hazards, such as carp, dust, meteors, and rarely, enemy fire. The shield room is located next to [[Engineering]]'s break room, on deck three. |
|
| |
|
| '''''(Please note that this guide assumes you have basic knowledge of the station layout, but limited knowledge of the engineering department layout specifically, and as such, will assume you can do things like “go to the surface level” without being told exactly what steps to take. If you need more help, please ask for help in-character.)''''' | | == Setting It Up == |
| | Setting the shields is one of the easiest jobs that an [[Engineer]] is tasked with. It's simply a matter of knowing the values to set the SMES, capacitor, and generator to. |
|
| |
|
| [[File:Shieldguide1.png]] | | [[File:Shield capacitor.png|thumb|The shield capacitor.]] |
| | [[File:Shield gen.png|thumb|The shield generator.]] |
|
| |
|
| So you’ve been tasked with setting the shields and you have no idea what to do, huh? What even are these ‘shields’ you’ve heard of? Why should you set them up anyways? It’s important to understand first off, that there’s two types of shields involved. We’ll quickly touch on what each type does, so you have an idea of what they should be used for.
| | # Set the SMES in the shield room to maximum input (1,500,000 watts), and the output to 1,400,000 watts. This is not a hard rule, and you can lower the values a bit if you want. |
| | # Using the <code>+++</code> button, set the '''shield capacitor''' to 1,250,000 watts. Click <code>Activate</code>. |
| | # Now, check out the '''shield generator'''. Set the coverage radius to 100. A coverage radius of 100 will cover all of the Horizon in a mostly-skintight blue bubble. |
| | # The '''charge rate''' can be set anywhere from 3 to 5. |
| | # The '''maximum field strength''' can be set from 3 to 6. Using higher values is reserved for rounds where both engines are running, and there's an immediate external danger to the Horizon. |
|
| |
|
| | Congrats! Shields should be spooling up. Assuming you have used a three-megawatt [[Supermatter]] setup, the shields will run mostly stable for the entire round. |
|
| |
|
| {| class="sortable" border="1" cellspacing="0" cellpadding="2" align="center"
| | ==Shield Tips and Troubleshooting== |
| ! style='background-color:Chocolate;'|Type of Shield
| | * Sections of shield that are destroyed (by carp bumping into them, meteors hitting them, [[Security Officer|Security Officers]] slapping them with a maglight, etc.) do not regenerate automatically. In order to restore the shield to its full integrity over the ship, you have to power off the shield generator and turn it on again. For obvious reasons, it's strongly recommended you don't do this when the Horizon is on a [[Guide to Piloting|tile full of hazards]]. |
| ! style='background-color:Chocolate;'|Style of Projection
| | * You can use a wrench on the capacitor and generator to move them anywhere you'd like. There may be an extremely rare case where it is recommended to seal something on the ship within a bubble, but in that case, you're probably best off using the emergency shields in Engineering Hard Storage instead. |
| ! style='background-color:Chocolate;'|Common Usage
| | * It is also worth noting that shields '''do not seal atmosphere'''. Don't try using them to hold a breach. |
| |-
| | * The shields can be easily sabotaged by snipping the wire nodes underneath them and the SMES they're attached to. Check the wires using your T-ray scanner if the shields aren't working. |
| !Hull Shield
| | * Shields can also drain a lot of power; if they're not turning on, check that you have any of the engines set up properly. It may be that another appliance on the ship is draining the power you need, or your engine isn't functioning at full capacity. |
| |Project shields on the surface of the station hull, like a skin surrounding it.
| |
| |Carp Migrations, Lost Drones from NTV Icarus, Hostile Forces
| |
| |-
| |
| !Bubble Shield
| |
| |Project shields around the station in a bubble, protecting the station and anything else within.
| |
| |Meteor Showers
| |
| |}
| |
|
| |
|
| | | {{Guides}} |
| With that said, let’s get to what we’re going to need to set up the shields, and where they’re stored.
| | [[Category:Guides]] |
| | |
| == Tools of the Trade: What you’ll need to set up the Hull and Bubble Shields, and where can you find it? ==
| |
| | |
| You begin by spawning in the Engineering Foyer. Let’s head to our left through the double doors and into the Engineering Storage room.
| |
| | |
| [[File:Shieldguide2.png]]
| |
| | |
| | |
| [[File:Shieldguide3.png]]
| |
| | |
| Once you are inside the Engineering Storage room, now what? The table below will list everything you need, as well as steps following that to gather each item.
| |
| | |
| {| class="sortable" border="1" cellspacing="0" cellpadding="2" align="center" | |
| ! style='background-color:Chocolate;'|Image of Item
| |
| ! style='background-color:Chocolate;'|Item Name
| |
| ! style='background-color:Chocolate;'|Item Usage
| |
| ! style='background-color:Chocolate;'|Where you can find it
| |
| |-
| |
| ![[File:Yellowgloves.png]]
| |
| |Insulated Gloves
| |
| |For protecting your precious hands from electrical shock. Note: DO NOT use Budget Insulated Gloves. Ever.
| |
| |Electrical Supplies Locker(<b><font color=red> Red Circle </font></b>)
| |
| |-
| |
| ![[File:Metal.png]]
| |
| |Steel Sheets
| |
| |For creating Steel Rods (See steps below)
| |
| |Supplies Rack(<b><font color=blue> Blue Circle </font></b>)
| |
| |-
| |
| ![[File:Glass.png]]
| |
| |Glass Sheets
| |
| |For creating Reinforced Glass Sheets (See Steps below)
| |
| |Supplies Rack(<b><font color=blue> Blue Circle </font></b>)
| |
| |-
| |
| ![[File:Airlock electronics.png]]
| |
| |Airlock Electronics
| |
| |For creating Airlocks/Windoors.
| |
| |Engi-Vend(<b><font color=green> Green Circle)
| |
| |}
| |
| | |
| | |
| *Step 1. Grab Insulated Gloves from the Electrical Supplies Locker and put them on your hands. This step is important, as you may lose your hands if you play with the power grid without protection.
| |
| | |
| *Step 2. Walk to your right and grab two '''Airlock Electronics''' by dispensing them from the Engi-Vend. Put them in your bag for now, we’ll come back to them later.
| |
| | |
| *Step 3. Walk over to your left and pick up the '''Steel Sheets'''. Use them in your hand and it should pull up a menu (Shown below).
| |
| | |
| | |
| '''The Menu'''
| |
| | |
| | |
| [[File:Shieldguide4.png]]
| |
| | |
| | |
| After you’ve opened the menu, you’re going to want to create thirty Metal Rods. You can do so by pressing the buttons “20x” and “10x”. You’ll get a message in your chat box that lists how many metal rods are in the stack.
| |
| | |
| *Step 4. Take your freshly created Metal Rods (they should be on the floor below you), and use them on the Glass Sheets to create fourteen Reinforced Glass Sheets. A message will once again be in the chat box to inform you of how many you’ve made so far.
| |
| | |
| *Step 5. Store the fourteen Reinforced Glass Sheets and remaining sixteen Metal Rods in your backpack for later. This is all the items we’ll need to complete shields setup.
| |
| | |
| When you’re done, your backpack inventory should look something like this. Congratulations, you’re prepared to start work on the shields themselves.
| |
| | |
| [[File:Shieldguide5.png]]
| |
| | |
| == The Shields Themselves: Where are they? ==
| |
| | |
| [[File:Shieldguide6.png]]
| |
| | |
| | |
| After you’ve gotten all of your materials, it’s time to grab the shield generators and their accompanying capacitors. They can be found North of the Engineering Storage room, inside Engineering Hard Storage. The image to the left shows exactly how to get to Engineering Hard Storage from where you were in the previous step.
| |
| | |
| Below is what you’ll find inside of an unmolested Hard Storage room. It’s important to remember that other engineers may have moved things around, so it may not look exactly the same.
| |
| | |
| [[File:Shieldguide7.png]]
| |
| | |
| The <font color=red>Red Circle</font> is the '''Bubble Shield''', while the <font color=blue>Blue Circle</font> is the '''Hull Shield'''. We’ll want to go ahead and drag all four pieces to the surface level. It is recommended that you have someone help you do this, as dragging all four to the surface level will take quite some time. When you reach the surface on the lifts, you’ll want to head to the area below the garden. The '''Bubble Shield''' will barely reach the Surface Command Dock, so it’s very important to put it in the correct place. The '''Hull Shield''' can go wherever, but it’s more efficient to put it right next to the Bubble Shield incase of emergency.
| |
| | |
| ==Setting Up Shield Containment: Looking Pretty==
| |
| | |
| | |
| Now that we’ve made it to the surface level, it’s time to begin working on our containment area for the shields. While not necessary, it keeps unauthorized crewmembers from tampering with the controls. This can be critical during an emergency when one assistant hitting the OFF switch can result in catastrophic damage to the station. Below, the area where we’ll set up the shields is shown. Let’s get down to business.
| |
| | |
| [[File:Shieldguide8.png]]
| |
| | |
| [[File:Shieldguide9.png]]
| |
| | |
| *Step 1. Use a crowbar to remove the floor tiles in the indicated pattern.
| |
| | |
| [[File:Shieldguide10.png]]
| |
| | |
| *Step 2.Use a cable coil to wire the ground in the indicated pattern. '''Warning: Be sure you are wearing your insulated gloves!'''
| |
| | |
| [[File:Shieldguide11.png]]
| |
| | |
| *Step 3. Use four of your fourteen '''''Reinforced Glass Sheets''''' to create the single-pane reinforced windows as shown. Secure them to the floor (apply screwdriver, crowbar, screwdriver).
| |
| | |
| [[File:Shieldguide12.png]]
| |
| | |
| *Step 4. Use the remaining '''''Reinforced Glass Sheets''''' to create two windoors.
| |
| | |
| [[File:Shieldguide13.png]]
| |
| | |
| *(Optional) Step 4.5. Right click the right windoor and click “Flip Windoor Assembly” to satisfy your OCD.
| |
| | |
| [[File:Shieldguide14.png]]
| |
| | |
| *Step 5. Secure the windoor assemblies with a wrench.
| |
| | |
| [[File:Shieldguide15.png]]
| |
| | |
| *Step 6. Use your remaining Metal Rods to reinforce the floor and windoor assemblies (do this simply by clicking on each floor tile once, as well as each windoor assembly once).
| |
| | |
| [[File:Shieldguide16.png]]
| |
| | |
| *Step 7. Replace the remaining missing floor tiles with the floor tiles you crowbarred up earlier.
| |
| | |
| [[File:Shieldguide17.png]]
| |
| | |
| *Step 8. Wire the windoor assemblies with your cable coil.
| |
| | |
| Before we continue, we’ll have to set up the '''''Airlock Electronics'''''. You’ll need to take them out of your backpack one at a time. Hold it in one hand, with your ID in the other. It should look something like this.
| |
| | |
| [[File:Shieldguide18.png]]
| |
| | |
| You’ll want to open the menu of your electronics. While it’s open, you’ll want to click “Swipe ID” with your ID in your active hand.
| |
| | |
| [[File:Shieldguide18.1.png]]
| |
| | |
| Click the 'Swipe ID' button.A new menu will pop up. It is very long, but we only care about a couple of buttons, listed below.
| |
| | |
| The first step is to change the Access Requirement to “<font color=green>ONE</font>” instead of “<font color=red>ALL</font>”. You can do this by clicking the “<font color=red>ALL</font>” button. You’ll also want to select the following three access requirements: “<font color=green>Atmospherics</font>”, “<font color=green>Bridge</font>”, and “<font color=green>Engine Room</font>”. This will ensure that only people with the correct knowledge to operate the shields can access it (Certain jobs, such as Janitor, for example, have access to the “Engineering” access requirement, but are not qualified to run the shield generators). Make sure you do this to both electronics. The correct setup is shown below, beside the default setup.
| |
| | |
| [[File:Shieldguide19.png]] [[File:Shieldguide20.png]]
| |
| | |
| Congratulations! You’ve set up the '''''Airlock Electronics'''''! With that covered, we’ll finish with our containment setup.
| |
| | |
| [[File:Shieldguide21.png]]
| |
| | |
| *Step 9. Install the '''''Airlock Electronics'''''. Be sure not to put both into one door, or you’ll be out of luck. This is a bug.
| |
| | |
| [[File:Shieldguide22.png]]
| |
| | |
| *Step 10. Use a crowbar to complete the reinforced windoors. Using an empty hand on them will open/close them.
| |
| | |
| This concludes the containment cell for our Shield Generators. We’ll continue from here with how to set up the generators themselves.
| |
| | |
| == Setting up the Shield Generators: The final steps ==
| |
| | |
| From here on out it’s fairly straight-forward. We want to begin by dragging both capacitors into the containment area. Be sure to rotate them so that they’re facing the correct directions (pictured below). Use a wrench to bolt them to the floor.
| |
| | |
| [[File:Shieldguide23.png]]
| |
| | |
| *Step 1. Wrench the capacitors into place like so. Be sure they are facing the correct direction (right click and select “Rotate Capacitor Clockwise” to change its direction).
| |
| | |
| [[File:Shieldguide24.png]]
| |
| | |
| [[File:Shieldguide25.png]]
| |
| | |
| *Step 2. Set the capacitor settings correctly. You’ll want to raise the Charge Rate to maximum using the far right “<font color=blue>[++++]</font>” button. The maximum is 400000 W. Be sure to “<font color=green>[Activate]</font>” the capacitor so it is <font color=green>Online</font>, otherwise it won’t actually do anything.
| |
| | |
| [[File:Shieldguide26.png]]
| |
| | |
| *Step 3. Wrench in the shield generators. The '''''Bubble''''' Shield should be on the '''RIGHT''', while the '''''Hull Shield''''' should be on the '''LEFT'''. While this is not mandatory, it allows the Bubble Shield to cover the Surface Command Dock by an additional meter.
| |
| | |
| *Step 4. Set the settings of the shield generators properly. The Coverage Radius (restart required) for '''both generators''' should be 100m. Use the “<font color=blue>+++</font>” button to quickly raise it to the maximum. The Charge Rate for '''both generators''' should be 0.3 Renwick/s. Use the “<font color=blue>++</font>” button to raise it up by one point (the default is 0.2 Renwick/s). Finally, the Maximum Field Strength for '''both generators''' should be 3 Renwick. Use the “<font color=blue>[min]</font>” button, followed by two presses of the “<font color=blue>+</font>” button to set it properly. The settings are shown correctly below.
| |
| | |
| '''''Default Setup'''''
| |
| [[File:Shieldguide27.png]]
| |
| | |
| '''''Correct Setup'''''
| |
| [[File:Shieldguide28.png]]
| |
| | |
| Congratulations! The shields are now properly setup for an emergency. Remember to leave them <font color=red>Offline</font> unless there’s a need for them, as they drain massive amounts of power. If you have any questions, you’re welcome to contact the author of this guide directly over discord or BYOND. You can also join the NT-ENG discord channel for help from our wonderful community! Have fun!
| |
| | |
| [[File:Shieldguide29.png]] | |
